1-to-6 RGB Splitter Cable $5.79 40 in stock | |
1-to-4 RGB Splitter Cable $5.21 40 in stock | |
More variations available Show |
Gelid RGB Splitter Cables
Designed for RGB enthusiasts to facilitate connection of numerous RGB fans or strips.
Features
- Excellent way of adding more RGB devices to your system
- Supplied with male plug adapters
- Compatible with 12V and 5V (A)RGB devices
The Gelid RGB Splitters allow you can easily expand one RGB or Addressable RGB (ARGB) header on your motherboard/controller to connect to multiple RGB devices, it’s even possible to daisy chaining multiple splitters altogether. Compatible with all standard 12V RGB and 5V Addressable RGB (ARGB) fans or strips. Features ultra durable cabling for extended longevity and Male Plug Adapters for seamless installation. The above images show the Male plugs installed, product comes with plugs uninstalled.
Specifications | 1-to-6 RGB Splitter | 1-to-4 RGB Splitter |
---|---|---|
Model number | CA-RGB-02 | CA-RGB-01 |
Colour | Black | Black |
Cable Length (mm) | 300 | 300 |
Input | 1x 4-pin Female RGB Connector | 1x 4-pin Female RGB Connector |
Output | 6x 4-pin Female RGB Connector | 4x 4-pin Female RGB Connector |
Included | 7 x Male Plug Adapters | 5 x Male Plug Adapters |
Warranty | 24 months | 24 months |
Specifications | 1-to-6 RGB Splitter | 1-to-4 RGB Splitter |
---|---|---|
Model number | CA-RGB-02 | CA-RGB-01 |
Colour | Black | |
Cable Length (mm) | 300 | |
Input | 1x 4-pin Female RGB Connector | |
Output | 6x 4-pin Female RGB Connector | 4x 4-pin Female RGB Connector |
Included | 7 x Male Plug Adapters | 5 x Male Plug Adapters |
Warranty | 24 months |
Product Resources
Top Cables and adapters

Gelid PWM Adaptor Cable for VGA Cooler Fans

Quiet PC IEC C13 UK Mains Power Cord, 1.8m (Type G)

Streacom PCI Express 1X Slot Riser Card Adapter Cable

Noctua NA-SYC1 4-Pin PWM Fan Y-Cables, 2 pack

Noctua NA-SEC1 4-Pin PWM Fan Extension Cables, 3 pack

Quiet PC IEC C13 Euro Mains Power Cord, 2m (Type F)

Noctua NA-SEC2 3-Pin Fan Extension Cables, 3 pack

Noctua NA-SRC7 4-Pin PWM Low-Noise Adaptors, 3 pack

Gelid PWM Y Cable, Connect two PWM fans to one socket

Noctua NA-SYC2 3-Pin Fan Y-Cables, 2 pack
Recently Viewed Products
“Akasa Newton S7”
“I purchased an Akasa Newton S7 case for my Intel NUC board. It arrived on time as described. However while this is a great product there are a few things about it I didn’t like. The first thing that caught my attention was that the heat sink is painted over. This will have a negative impact on the thermal performance, as paint does not have the conductivity that aluminum does (a copper block would have been even better). As I proceeded with the build I found that the cables for the front PCB were extremely stiff which meant that quite a bit of pressure was applied to my board where they attached. Also the case was not quite tall enough to accommodate the unyielding cables, meaning that I had difficulty installing in the bottom plate. The front LED also stopped working within a few days. And if you ripped your board from a NUC chassis, forget getting the internal wifi antennas to work inside the case. The supplied thermal pads for the CPU are also not a good idea as thermal grease is substantially better. I actually used some noctua NT-H1. However, all things considered I am happy with the product. My computer is now absolutely silent and the idle and load temps are actually better than they were with active cooling. Hopefully Akasa can fix some of my gripes in future iterations of this product.”