MenuSearch | Country: United States | Currency: USD
Excellent
3,688 reviews at Trustpilot.3,688 reviews
Kaze Jyuni 1200RPM Slip Stream 120mm Fan
Discontinued
More variations available Show

Scythe Kaze Jyuni 1200RPM Slip Stream 120mm Fan

The Scythe Slip Stream 120mm fan - designed to increase performance without compromising noise levels.

Scythe have released some new 120mm case fans, the “Slipstream 120mm Case Fan”. Their main aim with the new fans was to increase performance without compromising noise levels. The Slipstream 120mm Case Fans have been developed solely by Scythe engineers. They found out that by reducing the dimension of the centre hub and the wider surface area of the fan blade increased the airflow. There are a range of different fan speeds to choose from which meets the demand from a wide variety of users in the market. Silent users to power users now have more choice when it comes to choosing a suitable case fan.

Fan package includes 3-pin to 4-pin Molex adaptor and mounting screws
Fan package includes 3-pin to 4-pin Molex adaptor and mounting screws

Features

  1. Model number SY1225SL12M
  2. Quiet PC cooling fan
  3. Sleeve Bearings
  4. Very quiet only 24 dB(A) at 1200 RPM
  5. MTBF 30,000 hours

SpecificationsSlip Stream 1200
Fan size (edge to edge)120 mm
ManufacturerScythe
ModelSY1225SL12M
Air volume at full speed (12V), CFM ±10%68.5
Noise level at full speed (12V), dB(A)24.0
Fan speed at full speed (12V), RPM ±10%1200
Weight, g115
Approximate cable length, cm30
Life expectancy @ 25°C continuous use3.5 years
Power connector3-pin with 3-pin to 4-pin Molex adaptor
Bearing typeSleeve
Mounting hardware includedScrews
Fan depth25 mm
Rated voltage12 VDC
Warranty24 months
EAN barcode4571225041117
SpecificationsSlip Stream 1200
Fan size (edge to edge)120 mm
ManufacturerScythe
ModelSY1225SL12M
Air volume at full speed (12V), CFM ±10%68.5
Noise level at full speed (12V), dB(A)24.0
Fan speed at full speed (12V), RPM ±10%1200
Weight, g115
Approximate cable length, cm30
Life expectancy @ 25°C continuous use3.5 years
Power connector3-pin with 3-pin to 4-pin Molex adaptor
Bearing typeSleeve
Mounting hardware includedScrews
Fan depth25 mm
Rated voltage12 VDC
Warranty24 months
EAN barcode4571225041117

Customer Reviews

Great value!

,

I bought two of these to replace 2x screaming Delta fans in a rack mount case that’s holding 10 hard disks. These are very quiet and the hard disk temps are pretty much the same as they ware with the 40db fans they replaced. Definitely worth the money.

Super Fan

,

Very quiet and shifts air well, tried X red wing and noctua nf-12 in the past, but this shifts a lot more air and is just as quiet.

Scythe 1200RPM Slip Stream 120mm Fan

,

I was using Xilence Red Wing fans which are quite good but these produce much more airflow. Case temps have dropped by 7c instantly! The only negative is although they are pretty much silent they do have a slight bassy tone to them but this is a minor compared to the cooling performance gained. Well recommended!

Product Resources

FAQ

  • How do I measure fan size?

    The size of fan you need will generally be determined by the size of the fan fitting position in your PC case. The sizes of all the fans on our website are shown as measured along any one of the fan’s four sides, NOT the distance between the fan’s screw holes! Our most popular fan size is 120mm, followed by 80mm. This isn’t really dictated by customer preference, but more by recent designs of PC cases.

    As for the thickness (depth) of the fan, generally 25mm (1 inch) is by far the most common depth, although smaller fans can have shallower depths such as 15mm or even 10mm. All our fans are 25mm thick unless otherwise stated. If you have any questions about which fan you should order, please don’t hesitate to get in touch.

    If you know the distance between the fan mounting screw holes but don’t know what fan size to order, please see the following table. Note that the mounting hole measurements shown below are taken horizontally or vertically between the holes and not diagonally.

    Screw hole spacings and fan sizes

    32mm between screw holes:40mm fan size
    40mm between screw holes:50mm fan size
    50mm between screw holes:60mm fan size
    60mm between screw holes:70mm fan size
    72mm between screw holes:80mm fan size
    83mm between screw holes:92mm fan size
    105mm between screw holes:120mm fan size


  • I received a small cable (resistor) with my fan; what is it for?

    The resistor cable (also called Ultra Low Noise or ULN cable) is designed to allow the fan to run slightly slower for even quieter operation. The benefit in lower running noise is significant. Although the airflow will be reduced slightly, this usually has minimal effect on PC temperature. We would generally recommend using the ULN resistor cable for best results in almost all circumstances.

  • How can I tell which way the air blows through the fan?

    Hold the fan so that the round fan sticker is facing you. You are looking at the rear of the fan. When you plug the fan in, the air will be blowing towards you. If you want a fan to act as an air intake, then the fan sticker will be facing the inside of the case. Some fans also have two small arrows moulded into their plastic housing - one arrow shows the direction of airflow, and the other (at 90°) shows the direction of blade rotation.

  • Is it possible to use a 4-pin PWM fan or CPU cooler with a motherboard which has only 3-pin fan headers on it?

    Electrically, there is no problem doing this - the fourth pin on the fan cable is used purely for PWM control and is not needed in order for the fan to run. So you can plug the 4-pin fan connector onto the 3-pin motherboard fan header, leaving the fourth pin not connected to anything. The fan will potentially run at full speed, so if you would like to reduce the speed of the fan you will need to adjust the fan speed setting in your BIOS or use fan control software such as SpeedFan in Windows.

    The only other problem to consider is that occasionally, components immediately adjacent to the motherboard fan header can get in the way of the larger 4-pin fan connector, physically preventing connection. This problem also occurs if you try to use an in-line fan speed controller such as the one made by Gelid.

    Another avenue to explore is the possibility of using a bay-mounted fan controller. Several models are available now which provide 4-pin fan headers, so this is an easy way to use 4-pin PWM fans in a PC system which has only 3-pin fan headers on its motherboards. When using this method, you may find it necessary to disable any fan warning settings in your motherboard BIOS, since the motherboard may incorrectly believe that its CPU fan has failed when the fan is connected to a fan controller rather than directly to the motherboard itself.

Top Ultra-Quiet 120mm fans

Recently Viewed Products

“Quiet Fans”

“I purchased 3 of these to replace the noisy ones in my Netgear 48 port switch - the difference is amazing.

Cheers

John”

(Review via Trustpilot)